İsim Verme ve Interface Durumları Huawei

Related Articles

Huawei Cihazlarda Cisco İp Phone Ce Cdp Kullanımı

4 Temmuz 2019

VPLS Huawei

4 Temmuz 2019

Huawei Firewall ile Cisco router arasında BGP konfigürasyonu

29 Haziran 2019

1.Temel Ethernet switch konfigürasyonu.
Cihazlara isimlerini verelim ve G0/0/9 ve G0/0/10 interfaceleri inceleyelim.
system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname Router1
[Router1]display interface GigabitEthernet 0/0/9
GigabitEthernet0/0/9 current state : UP
Line protocol current state : UP
Description:HUAWEI, Quidway Series, GigabitEthernet0/0/9 Interface
Switch Port,PVID : 1,The Maximum Frame Length is 1600
IP Sending Frames’ Format is PKTFMT_ETHNT_2, Hardware address is 80fb-06e8-d3c0
Port Mode: COMMON COPPER
Speed : 1000, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec,Record time: –
Output peak rate 0 bits/sec,Record time: –
Input: 0 packets, 0 bytes
Unicast : 0,Multicast : 0
Broadcast : 0,Jumbo : 0
CRC : 0,Giants : 0
Jabbers : 0,Throttles : 0
Runts : 0,DropEvents : 0
Alignments : 0,Symbols : 0
Ignoreds : 0,Frames : 0
Discard : 0,Total Error : 0
Output: 0 packets, 0 bytes
Unicast : 0,Multicast : 0
Broadcast : 0,Jumbo : 0
Collisions : 0,Deferreds : 0
Late Collisions: 0,ExcessiveCollisions: 0
Buffers Purged : 0
Discard : 0,Total Error : 0
Input bandwidth utilization threshold : 100.00%
Output bandwidth utilization threshold: 100.00%
Input bandwidth utilization : 0.00%
Output bandwidth utilization : 0.00%

[Router1]display interface GigabitEthernet 0/0/10
GigabitEthernet0/0/10 current state : UP
Line protocol current state : UP
Description:HUAWEI, Quidway Series, GigabitEthernet0/0/10 Interface
Switch Port,PVID : 1,The Maximum Frame Length is 1600
IP Sending Frames’ Format is PKTFMT_ETHNT_2, Hardware address is 80fb-06e8-d3c0
Port Mode: COMMON COPPER
Speed : 1000, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
input rate 0 bits/sec, 0 packets/sec
Last 300 Last 300 seconds seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 0 bits/sec,Record time: –
Output peak rate 0 bits/sec,Record time: –
Input: 0 packets, 0 bytes
Unicast : 0,Multicast : 0
Broadcast : 0,Jumbo : 0
CRC : 0,Giants : 0
Jabbers : 0,Throttles : 0
Runts : 0,DropEvents : 0
Alignments : 0,Symbols : 0
Ignoreds : 0,Frames : 0
Discard : 0,Total Error : 0
Output: 0 packets, 0 bytes
Unicast : 0,Multicast : 0
Broadcast : 0,Jumbo : 0
Collisions : 0,Deferreds : 0
Late Collisions: 0,ExcessiveCollisions: 0
Buffers Purged : 0
Discard : 0,Total Error : 0
Input bandwidth utilization threshold : 100.00%
Output bandwidth utilization threshold: 100.00%
Input bandwidth utilization : 0.00%
Output bandwidth utilization : 0.00%

Huawei switchlerde auto-negotiation aktif olarak gelir. Router1 ve Router2 cihazlarında G0/0/9 ve G0/0/10 portlarını manuel olarak hız ve duplex durumlarını ayarlayalım.
Router1 ‘de G0/0/9 ve G0/0/10 portlarını 100 Mbit/s ve full duplex modda çalışması için gerekli ayarları yapalım. İnterface’nin hızını ve duplex modunu değiştirmeden önde auto-negotiation’u kapatalım. Auto-negotiation açıkken port durumunu bağlı olduğu interface’e göre otomatik olarak ayarlayacaktır, açıkken bu ayarları manuel olarak giremeyiz.
[Router1]interface GigabitEthernet 0/0/9
[Router1-GigabitEthernet0/0/9]undo negotiation auto
[Router1-GigabitEthernet0/0/9]speed 100
[Router1-GigabitEthernet0/0/9]duplex full
[Router1-GigabitEthernet0/0/9]quit
[Router1]interface GigabitEthernet 0/0/10
[Router1-GigabitEthernet0/0/10]undo negotiation auto
[Router1-GigabitEthernet0/0/10]speed 100
[Router1-GigabitEthernet0/0/10]duplex full

Router2 için de G0/0/9 ve G0/0/10 portlarını 100 Mbit/s ve full duplex modda çalışması için ayarlayalım.
system-view
Enter system view, return user view with Ctrl+Z.
[Huawei]sysname CLIGURU-S2
[Router2]interface GigabitEthernet 0/0/9
[Router2-GigabitEthernet0/0/9]undo negotiation auto
[Router2-GigabitEthernet0/0/9]speed 100
[Router2-GigabitEthernet0/0/9]duplex full
[Router2-GigabitEthernet0/0/9]quit
[Router2]interface GigabitEthernet 0/0/10
[Router2-GigabitEthernet0/0/10]undo negotiation auto
[Router2-GigabitEthernet0/0/10]speed 100
[Router2-GigabitEthernet0/0/10]duplex full

Router1’in G0/0/9 ve G0/0/10 portlarının rate ve duplex modları olarak ayarladık, şimdi kontrol edelim.
[Router1]display interface GigabitEthernet 0/0/10
GigabitEthernet0/0/10 current state : UP
Line protocol current state : UP
Description:HUAWEI, Quidway Series, GigabitEthernet0/0/10 Interface
Switch Port,PVID : 1,The Maximum Frame Length is 1600
IP Sending Frames’ Format is PKTFMT_ETHNT_2, Hardware address is 80fb-06e8-d3c0
Port Mode: COMMON COPPER
Speed : 100, Loopback: NONE
Duplex: FULL, Negotiation: DISABLE
Mdi : AUTO