Interfacelerin IP Address ve Genel Ayarlamaları Huawei

Related Articles

Huawei Cihazlarda Cisco İp Phone Ce Cdp Kullanımı

4 Temmuz 2019

VPLS Huawei

4 Temmuz 2019

Huawei Firewall ile Cisco router arasında BGP konfigürasyonu

29 Haziran 2019

Routerlerin haberleşmesi için gerekli olan ip address ve arayüzlerini vererek bilgilendirme de yapabiliriz.
[Router1]interface GigabitEthernet 0/0/0
[Router1-GigabitEthernet0/0/0]ip add 192.168.1.1 24
[Router1-GigabitEthernet0/0/0]description Bu interface CLIGURU-R2’nin G0/0/0 portuna bagli
Router1-G0/0/0 altında yaptıgımız tüm işlemleri display this komutu ile görebiliriz.
[Router-GigabitEthernet0/0/0]display this
[V200R003C01SPC900] #
interface GigabitEthernet0/0/0
description Bu interface Router2’nin G0/0/0 portuna bagli
ip address 192.168.1.1 255.255.255.0
#
Return

Arayüz açıklamalarını görüntülemek için display interface komutunu kullanabiliriz.
[Router1]display interface GigabitEthernet 0/0/0
GigabitEthernet0/0/0 current state :UP
Line protocol current state : UP
Description: Bu interface Router2’nin G0/0/0 portuna bagli
Route Port,The Maximum Transmit Unit is 1500
Internet Address is 192.168.1.1/24
IP Sending Frames’ Format is PKTFMT_ETHNT_2, Hardware address is d46a-a877-0a41
Last physical up time : 2014-09-20 17:18:32Last physical down time : 2014-09-20 17:25:53
Current system time: 2014-09-20 15:28:30+07:00
Port Mode: FORCE COPPER
Speed : 100, Loopback: NONE
Duplex: FULL, Negotiation: ENABLE
Mdi : AUTO
Last 300 seconds input rate 0 bits/sec, 0 packets/sec
Last 300 seconds output rate 0 bits/sec, 0 packets/sec
Input peak rate 3168 bits/sec,Record time: 2014-09-20 17:21:41
Output peak rate 560 bits/sec,Record time: 2014-09-20 17:19:51
Input: 360 packets, 59847 bytes
Unicast: 44, Multicast: 256
Broadcast: 60, Jumbo: 0
Discard: 0, Total Error: 0
CRC: 0, Giants: 0
Jabbers: 0, Throttles: 0
Runts: 0, Symbols: 0
Ignoreds: 0, Frames: 0
Output: 21 packets, 7371 bytes
Unicast: 0, Multicast: 0
Broadcast: 21, Jumbo: 0
Discard: 0, Total Error: 0
Collisions: 0, ExcessiveCollisions: 0
Late Collisions: 0, Deferreds: 0
Input bandwidth utilization threshold : 100.00%
Output bandwidth utilization threshold: 100.00%
Input bandwidth utilization : 0%
Output bandwidth utilization : 0%

Cihazların karşılıklı konuşabilmeleri için Router2 cihazınında ip address ayarlamalarını yapılandırmamız gerekir.
[Router2]interface GigabitEthernet 0/0/0
[Router2-GigabitEthernet0/0/0]ip add 192.168.1.2 24
[Router2-GigabitEthernet0/0/0]descriptionThis interface connects to CLIGURU-R1-G0/0/0

Cihazların karşılıklı haberleştiğini anlamamız için ise ping komutunu kullanalım.
[Router1]ping 192.168.1.2
PING 192.168.1.2: 56 data bytes, press CTRL_C to break
Reply from 192.168.1.2: bytes=56 Sequence=1 ttl=255 time=50 ms
Reply from 192.168.1.2: bytes=56 Sequence=2 ttl=255 time=30 ms
Reply from 192.168.1.2: bytes=56 Sequence=3 ttl=255 time=50 ms
Reply from 192.168.1.2: bytes=56 Sequence=4 ttl=255 time=50 ms
Reply from 192.168.1.2: bytes=56 Sequence=5 ttl=255 time=10 ms