Inter VLAN Routing Huawei

Related Articles

Huawei Cihazlarda Cisco İp Phone Ce Cdp Kullanımı

4 Temmuz 2019

VPLS Huawei

4 Temmuz 2019

Huawei Firewall ile Cisco router arasında BGP konfigürasyonu

29 Haziran 2019

Inter VLAN Routing Huawei

1. Genel konfigürasyon
   Router1,Router3 ve Switch1 konfigürasyonu ile başlayalım, cihazlara isim ve ip addresslerini verelim.
   Router1 için G0/0/1’e ip address 10.0.4.1/24 olarak verelim.
   system-view
   Enter system view, return user view with Ctrl+Z.
   [Huawei]sysname Router1
   [Router1]interface GigabitEthernet 0/0/1
   [Router1-GigabitEthernet0/0/1]ip address 10.0.4.1 24
   Router3 için G0/0/1’e ip address 10.0.8.1/24 olarak verelim.
   system-view
   Enter system view, return user view with Ctrl+Z.
   [Huawei]sysname Router3
   [Router3]interface GigabitEthernet 0/0/1
   [Router3-GigabitEthernet0/0/1]ip address 10.0.8.1 24
2. Vlan konfigürasyonu .
   Switch1’de vlan 4 ve 8 oluşturalım. Interface G0/0/1 VLAN 4 ve interface G0/0/3’de VLAN 8 dahil olacak şekilde ayarlayalım.
   system-view
   Enter system view, return user view with Ctrl+Z.
   [Huawei]sysname Switch1
   [Switch1]vlan batch 4 8
   Info: This operation may take a few seconds. Please wait for a moment…done.
   [Switch1]interface GigabitEthernet 0/0/1
   [Switch1-GigabitEthernet0/0/1]port link-type access
   [Switch1-GigabitEthernet0/0/1]port default vlan 4
   [Switch1-GigabitEthernet0/0/1]quit
   [Switch1]interface GigabitEthernet 0/0/3
   [Switch1-GigabitEthernet0/0/3]port link-type access
   [Switch1-GigabitEthernet0/0/3]port default vlan 8
   [Switch1-GigabitEthernet0/0/3]quit
   Interface G0/0/2 de VLAN 4 ve 8’in iletişime geçebilmesi için interface’i trunk olarak ayarlayalım.
   [Switch1]interface GigabitEthernet 0/0/2
   [Switch1-GigabitEthernet0/0/2]port link-type trunk
   [Switch1-GigabitEthernet0/0/2]port trunk allow-pass vlan 4 8
3. Router2 üzerinden Sub-interface ve VLAN routing konfigürasyonu.
   Sub-interface G0/0/1.1 ‘i oluşturalım ve VLAN 4 için gateway olacak şekilde konfigure edelim ve G0/0/1.3 için VLAN 8’e gateway olarak konfigure edelim.
   system-view
   Enter system view, return user view with Ctrl+Z.
   [Huawei]sysname Router2
   [Router2]interface GigabitEthernet 0/0/1.1
   [Router2-GigabitEthernet0/0/1.1]ip address 10.0.4.254 24
   [Router2-GigabitEthernet0/0/1.1]dot1q termination vid 4
   [Router2-GigabitEthernet0/0/1.1]arp broadcast enable
   [Router2-GigabitEthernet0/0/1.1]quit
   [Router2]interface GigabitEthernet 0/0/1.3
   [Router2-GigabitEthernet0/0/1.3]ip address 10.0.8.254 24
   [Router2-GigabitEthernet0/0/1.3]dot1q termination vid 8
   [Router2-GigabitEthernet0/0/1.3]arp broadcast enable
   Router1 ve Router3 arasındaki bağlantıyı kontrol edelim.
   ping 10.0.8.1
   PING 10.0.8.1: 56 data bytes, press CTRL_C to break
   Request time out
   Request time out
   Request time out
   Request time out
   Request time out
   — 10.0.8.1 ping statistics —
   5 packet(s) transmitted
   0 packet(s) received
   100.00% packet loss
   Router1 ve Router3 üzerinde default route konfigurasyonu yapalım.
   [Router1]ip route-static 0.0.0.0 0.0.0.0 10.0.4.254
   [Router3]ip route-static 0.0.0.0 0.0.0.0 10.0.8.254
   Tekrar Router1 ve Router3 bağlantısını kontrol edelim.
   ping 10.0.8.1
   PING 10.0.8.1: 56 data bytes, press CTRL_C to break
   Reply from 10.0.8.1: bytes=56 Sequence=1 ttl=254 time=290 ms
   Reply from 10.0.8.1: bytes=56 Sequence=2 ttl=254 time=160 ms
   Reply from 10.0.8.1: bytes=56 Sequence=3 ttl=254 time=120 ms
   Reply from 10.0.8.1: bytes=56 Sequence=4 ttl=254 time=60 ms
   Reply from 10.0.8.1: bytes=56 Sequence=5 ttl=254 time=90 ms
   — 10.0.8.1 ping statistics —
   5 packet(s) transmitted
   5 packet(s) received
   0.00% packet loss
   round-trip min/avg/max = 60/144/290 ms
   display ip routing-table
   Route Flags: R – relay, D – download to fib
   —————————————————————————
   Routing Tables: Public
   Destinations : 8 Routes : 8
   Destination/Mask Proto Pre Cost Flags NextHop Interface
   10.0.4.0/24 Direct 0 0 D 10.0.4.254 GigabitEthernet0/0/1.1
   10.0.4.1/32 Direct 0 0 D 10.0.4.1 GigabitEthernet0/0/1.1
   10.0.4.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1.1
   10.0.8.0/24 Direct 0 0 D 10.0.8.254 GigabitEthernet0/0/1.3
   10.0.8.1/32 Direct 0 0 D 10.0.8.1 GigabitEthernet0/0/1.3
   10.0.8.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet0/0/1.3
   127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
   127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
   Final …
   display current-configuration
   #
   sysname Router1
   #
   interface GigabitEthernet0/0/1
   ip address 10.0.4.1 255.255.255.0
   #
   ip route-static 0.0.0.0 0.0.0.0 10.0.4.254
   #
   user-interface con 0
   user-interface vty 0 4
   user-interface vty 16 20
   #
   Return
   display current-configuration
   #
   sysname Router2
   #
   interface GigabitEthernet0/0/1
   #
   interface GigabitEthernet0/0/1.1
   dot1q termination vid 4
   ip address 10.0.4.254 255.255.255.0
   arp broadcast enable
   #
   interface GigabitEthernet0/0/1.3
   dot1q termination vid 8
   ip address 10.0.8.254 255.255.255.0
   arp broadcast enable
   #
   user-interface con 0
   user-interface vty 0 4
   user-interface vty 16 20
   #
   Return
   [Router3]display current-configuration
   #
   sysname Router3
   #
   interface GigabitEthernet0/0/1
   ip address 10.0.8.1 255.255.255.0
   #
   ip route-static 0.0.0.0 0.0.0.0 10.0.8.254
   #
   user-interface con 0
   user-interface vty 0 4
   user-interface vty 16 20
   #
   Return
   display current-configuration
   #
   sysname Switch1
   #
   vlan batch 4 8
   #
   interface GigabitEthernet0/0/1
   port link-type access
   port default vlan 4
   #
   interface GigabitEthernet0/0/2
   port link-type trunk
   port trunk allow-pass vlan 4 8
   #
   interface GigabitEthernet0/0/3
   port link-type access
   port default vlan 8
   #
   user-interface con 0
   user-interface vty 0 4
   #
   return